hh.sePublikasjoner
Endre søk
Begrens søket
1 - 1 of 1
RefereraExporteraLink til resultatlisten
Permanent link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Treff pr side
  • 5
  • 10
  • 20
  • 50
  • 100
  • 250
Sortering
  • Standard (Relevans)
  • Forfatter A-Ø
  • Forfatter Ø-A
  • Tittel A-Ø
  • Tittel Ø-A
  • Type publikasjon A-Ø
  • Type publikasjon Ø-A
  • Eldste først
  • Nyeste først
  • Skapad (Eldste først)
  • Skapad (Nyeste først)
  • Senast uppdaterad (Eldste først)
  • Senast uppdaterad (Nyeste først)
  • Disputationsdatum (tidligste først)
  • Disputationsdatum (siste først)
  • Standard (Relevans)
  • Forfatter A-Ø
  • Forfatter Ø-A
  • Tittel A-Ø
  • Tittel Ø-A
  • Type publikasjon A-Ø
  • Type publikasjon Ø-A
  • Eldste først
  • Nyeste først
  • Skapad (Eldste først)
  • Skapad (Nyeste først)
  • Senast uppdaterad (Eldste først)
  • Senast uppdaterad (Nyeste først)
  • Disputationsdatum (tidligste først)
  • Disputationsdatum (siste først)
Merk
Maxantalet träffar du kan exportera från sökgränssnittet är 250. Vid större uttag använd dig av utsökningar.
  • 1.
    Andersson, Viktor
    et al.
    Högskolan i Halmstad, Sektionen för ekonomi och teknik (SET).
    Olsén, Martin
    Högskolan i Halmstad, Sektionen för ekonomi och teknik (SET).
    Kilhus i plast: Omläggning av stålprodukt till produkt i plast2010Independent thesis Basic level (degree of Bachelor), 15 poäng / 22,5 hpOppgave
    Abstract [en]

    Abstract

    Our bachelor degree thesis was carried out in collaboration with Ivar Petterssons Järnmanufaktur AB in Smålandsstenar. We were asked to replace their wedge housing, used to fasten the wires to the power lines, with a similar structure in a plastic material. The idea for this project started with Ivar Petterssons Järnmanufaktur AB having problems with the casting quality that forced them to perform expensive tests on each of the wedge houses to ensure the quality. They are currently produced in China which is also a major drawback because it requires expensive long delivery times.

    The method we used is Fredy Olsson's Princip- and Primärkonstuktion (1995). We have consistently been in the project on so-called "broad front", which means that you create several sketches, ideas and changes in parallel, and then evaluates all. With this method we were able to largely concentrate on the current part of the project, rather than using the more time-consuming "trail and error" method, which is basically doing one idea at a time, and evaluate them one by one.

    At first we were very optimistic and thought we would be able to order form for the injection moulding process, but as the project progressed we found we were not certain that the product would hold and we were forced to present the solution as a concept that will require testing before it’s finished, and not a finished solution.The results we presented for Ivar Pettersssons Järnmanufaktur is a complete drawing on our primary solution, including the release angles. This is because when they decide to go forth with the project, it will be possible to produce a tool without having to make changes to the drawings. Temporary financial calculation shows that the savings may be realized around 1 300 000 SEK by switching to a plastic construction. However we have not been able to verify hours and therefore no cost estimates for the testing done in Sweden, so the actual amount of money saved is larger.

1 - 1 of 1
RefereraExporteraLink til resultatlisten
Permanent link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf