hh.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Alternative descriptions of roughness for cylinder liner production
Halmstad University, School of Business and Engineering (SET), Mechanical Engineering and Industrial Design (MTEK), Functional Surfaces.
Rzeszow University of Technology, Poland.
Halmstad University, School of Business and Engineering (SET), Mechanical Engineering and Industrial Design (MTEK), Functional Surfaces.ORCID iD: 0000-0001-8058-1252
Halmstad University, School of Business and Engineering (SET), Mechanical Engineering and Industrial Design (MTEK).
2009 (English)In: Journal of Materials Processing Technology, ISSN 0924-0136, E-ISSN 1873-4774, Vol. 209, no 4, p. 1936-1942Article in journal (Refereed) Published
Abstract [en]

The roughness of stratified surfaces such as cylinder liners, produced by plateau honing, is functionally important in their tribology but is notoriously difficult to characterise. An issue in manufacturing quality control related to their tribological function is the comparative ability of various roughness characterisation systems. In this paper the Rk family of parameters is compared with the Rq family as regards stability and discrimination. When coefficients of variation of the two parameter families are compared as a measure of stability, CVs of individual parameters vary between 8% and 20% but do not seem to indicate a clear advantage to either family. When the correlation of parameters within and between the two groups is computed as a measure of relative discriminative ability, many parameters are found to be highly correlated, to the point where values of Rpk and Rpq are effectively indistinguishable. The relative robustness of the parameters is also established by simulation of surface or measurement artefacts: outlying peaks and valleys, high-frequency noise, changes in stylus or skid radius, changes in high-pass filter and in assessment length. Outlying peaks cause a large increase in Rpk, while outlying valleys have little effect. The Rq parameters are more sensitive to high-frequency noise than the Rk parameters. Increasing the stylus radius reduced the valley parameters, while adding a 25 mm radius skid increased Rk and Rpq by as much as 15%. Increasing the short-wavelength cut-off from 2.5 m to 8 m reduced most parameters, particularly the peak parameters, while replacing the robust Gaussian filter used throughout by a valley-suppression filter had little effect. Finally reducing the assessment length from 17 mm to 4 mm decreased the values of many parameters by up to 11%. Increasing plateau honing time decreased plateau roughness, while increasing pressure during coarse honing increased valley roughness, but these changes could not be correlated with roughness parameters. This suggests that the optimum parameter set has not yet been found. 2008 Elsevier B.V. All rights reserved.

Place, publisher, year, edition, pages
Amsterdam: Elsevier, 2009. Vol. 209, no 4, p. 1936-1942
Keywords [en]
Honing, Control theory, Customer satisfaction, Cylinders (shapes), Friction, High pass filters, Landforms, Point groups, Quality assurance, Quality function deployment, Surface properties, Surface roughness, System stability, Total quality management, Tribology
National Category
Engineering and Technology
Identifiers
URN: urn:nbn:se:hh:diva-3338DOI: 10.1016/j.jmatprotec.2008.04.059ISI: 000263802100036Scopus ID: 2-s2.0-58249130723OAI: oai:DiVA.org:hh-3338DiVA, id: diva2:281353
Available from: 2009-12-15 Created: 2009-12-01 Last updated: 2018-03-23Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records BETA

Anderberg, CeciliaRosén, Bengt-GöranThomas, T. R.

Search in DiVA

By author/editor
Anderberg, CeciliaRosén, Bengt-GöranThomas, T. R.
By organisation
Functional SurfacesMechanical Engineering and Industrial Design (MTEK)
In the same journal
Journal of Materials Processing Technology
Engineering and Technology

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 328 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf