hh.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of the measurement size on the robustness of the assessment of the features specific for cylinder liner surfaces
Högskolan i Halmstad, Akademin för ekonomi, teknik och naturvetenskap, Maskinteknisk produktframtagning (MTEK), Funktionella ytor.ORCID-id: 0000-0003-3149-4296
Volvo Group Trucks Technology, Gothenburg, Sweden.
Högskolan i Halmstad, Akademin för ekonomi, teknik och naturvetenskap, Maskinteknisk produktframtagning (MTEK), Funktionella ytor.ORCID-id: 0000-0001-8058-1252
2014 (Engelska)Ingår i: Surface Topography: Metrology and Properties, ISSN 2051-672X, Vol. 2, nr 1, artikel-id 014013Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The quality of the cylinder liner surface is of great importance due to its impact on the fuel/oil consumption and emissions of the internal combustion engine. A good liner function depends on the size and distribution of the deep honing grooves and the amount of the cold work material (Blechmantel) left inside the grooves after finishing. A fast evaluation of these features requires optical three-dimensional measurements with a large area and good resolution, but many interferometers used today have limited resolution when measuring larger areas. To find out how the measurement size and resolution would affect the quantification and the variation of the parameters, two objectives, 2.5 ×  and 10 × , were used for measuring a cylinder liner from a truck engine. The Blechmantel was of special interest as it first comes into contact with piston/rings, detaches as particles and wears the running surfaces. The 2.5 ×  objective showed more robust assessment than the 10 ×  one, manifested by a lower coefficient of variation for the parameters describing the features: Blechmantel, groove width and height, groove balance and number of grooves. This means that fewer measurements are required if a 2.5 ×  objective is used in production and hence the time and cost of the liner would be decreased. © 2014 IOP Publishing Ltd.

Ort, förlag, år, upplaga, sidor
Bristol: Institute of Physics Publishing (IOPP), 2014. Vol. 2, nr 1, artikel-id 014013
Nationell ämneskategori
Annan maskinteknik
Identifikatorer
URN: urn:nbn:se:hh:diva-24765DOI: 10.1088/2051-672X/2/1/014013Scopus ID: 2-s2.0-84979196353OAI: oai:DiVA.org:hh-24765DiVA, id: diva2:700164
Forskningsfinansiär
EnergimyndighetenTillgänglig från: 2014-03-03 Skapad: 2014-03-03 Senast uppdaterad: 2017-03-16Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopusFull text

Personposter BETA

Dimkovski, ZlateRosén, Bengt-Göran

Sök vidare i DiVA

Av författaren/redaktören
Dimkovski, ZlateRosén, Bengt-Göran
Av organisationen
Funktionella ytor
Annan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 201 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf