hh.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
A study on the effect of surface topography on rough friction in roller contact
Department of Production Engineering, Chalmers University of Technology, Gothenburg, Sweden.
Högskolan i Halmstad, Akademin för ekonomi, teknik och naturvetenskap, Maskinteknisk produktframtagning (MTEK), Funktionella ytor.ORCID-id: 0000-0001-8058-1252
Volvo Car Corporation, Gothenburg, Sweden.
Volvo Technological Development, Gothenburg, Sweden.
2003 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 254, nr 11, s. 1162-1169Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The friction behaviour of gear teeth in the context of tribology can have a strong effect on housing vibration, noise and efficiency. One of the parameters that greatly influences the friction under certain running conditions is surface roughness. In this work, rough friction was studied in lubricated sliding of roller surfaces, which were manufactured to simulate the real gear surfaces. By examining 3D surface topography of two mating bodies, both surface roughness and its effect on friction behaviour can be studied. In a previous study, a rough-friction test rig has been designed, constructed and initially verified. The types of surfaces involved in this study are ground, shot-peened, phosphated and electrochemically deburred. These rollers were subjected to the same friction testing procedures. Roller surfaces were then examined, and correlation between the topography and the frictional behaviour was analysed. Friction behaviour was interpreted in terms of Stribeck curves (friction coefficient as the function of Hersey parameter (ην/p)). The results showed that electrochemically deburred and certain phosphated surfaces provide lower friction coefficient values which are competitive to fine-ground surfaces in lubricated rolling/sliding contact. © 2003 Elsevier Science B.V. All rights reserved.

Ort, förlag, år, upplaga, sidor
Amsterdam: Elsevier, 2003. Vol. 254, nr 11, s. 1162-1169
Nyckelord [en]
Surface Topography, Wear of materials, Friction, Rolling, Sliding mode control, Surface roughness, Tribology, Gears
Nationell ämneskategori
Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Identifikatorer
URN: urn:nbn:se:hh:diva-3560DOI: 10.1016/S0043-1648(03)00329-6ISI: 000185448900016Scopus ID: 2-s2.0-0042856282OAI: oai:DiVA.org:hh-3560DiVA, id: diva2:284870
Konferens
10th Nordic Conference on Tribology, NORDTRIB 2002, 9-12th June, KTH, Stockholm, Sweden, 2002
Anmärkning

Funding: Volvo Car Corporation (VCC), Volvo Technological Development Corporation (VTDC) & the Swedish Board for Vehicular Research

Tillgänglig från: 2010-01-08 Skapad: 2009-12-01 Senast uppdaterad: 2018-01-12Bibliografiskt granskad
Ingår i avhandling
1. Gear tribology: friction and surface topography
Öppna denna publikation i ny flik eller fönster >>Gear tribology: friction and surface topography
2005 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The quest for energy efficiency leads to the development of highly efficient power transmissions for vehicles. Gears are some of the most rugged and durable torque transmitters among machine elements. Friction between sliding surfaces at gear teeth is one major source of power loss. To increase efficiency and reduce damage accumulation in gears has always been a background motivation to this thesis. It focuses on the frictional performance of manufactured gear surfaces with emphasis on the effect of surface topography and the orientation of its lay.

To achieve the goal of this work, a test rig was designed and constructed. The rig makes it possible to examine gear tooth friction on double crowned rollers. Five alternative gear-finishing processes are implemented in roller surface preparation. They comprise grinding, shotpeening, phosphating, chemical deburring and DLC coating. Theoretically, a friction model is suggested which helps to explain some of the testing results. Advanced surface metrology techniques and statistical tools are implemented in identifying surface features that influence friction.

The result demonstrates that surface topography is a significant factor affecting the lubricated frictional behaviour. For ground-finishing, the smoother the surfaces are finished, the lower friction coefficient they show. Chemical deburring and DLC coating as well as certain degrees of phosphating provide minimum friction coefficient and improved load carrying capacity, which are competitive to fine-ground finishing. Properly designed lay combinations of meshing gear surfaces can minimise friction and improve gear transmission efficiency. Theoretically, the friction coefficient can be explained by means of a combination of the slide-to-roll ratio and the real mean contact pressure within the range of loads considered in this thesis. Finally, features that correlate surface topography to friction are identified.

Ort, förlag, år, upplaga, sidor
Göteborg: Chalmers university of technology, 2005. s. 46
Serie
Doktorsavhandlingar vid Chalmers tekniska högskola. Ny serie, ISSN 0346-718X ; 2263
Nyckelord
Friction, Surface topography, Toughness, Lay, Gears, Power transmission
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
urn:nbn:se:hh:diva-721 (URN)2082/1070 (Lokalt ID)91-7291-581-1 (ISBN)2082/1070 (Arkivnummer)2082/1070 (OAI)
Disputation
2005-04-08, KB Salen, K-huset, Chalmers Tekniska Högskola, Göteborg, 13:00 (Engelska)
Opponent
Handledare
Tillgänglig från: 2007-06-11 Skapad: 2007-06-11 Senast uppdaterad: 2018-03-23Bibliografiskt granskad
2. Effect of rough surface anisotropy on friction in gears
Öppna denna publikation i ny flik eller fönster >>Effect of rough surface anisotropy on friction in gears
2002 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Ort, förlag, år, upplaga, sidor
Göteborg: Chalmers tekniska högsk., 2002. s. vii, 28
Serie
Thesis for the degree of licentiate of engineering, ISSN 1651-0984 ; 8
Nyckelord
Friction, Surface topography, Roughness, Lay, Gears, Efficiency, Power transmission
Nationell ämneskategori
Teknik och teknologier Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Identifikatorer
urn:nbn:se:hh:diva-1376 (URN)2082/1755 (Lokalt ID)2082/1755 (Arkivnummer)2082/1755 (OAI)
Presentation
(Engelska)
Opponent
Handledare
Anmärkning

Funding: The Swedish Board for Vehicular Research & Volvo

Tillgänglig från: 2008-04-29 Skapad: 2008-04-29 Senast uppdaterad: 2018-01-13Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Rosén, Bengt-Göran

Sök vidare i DiVA

Av författaren/redaktören
Rosén, Bengt-Göran
Av organisationen
Funktionella ytor
I samma tidskrift
Wear
Tribologi (ytteknik omfattande friktion, nötning och smörjning)

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 431 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf