hh.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Quantification of Blechmantel Effect on Wear of Cylinder Bore Microtopography
Högskolan i Halmstad, Sektionen för ekonomi och teknik (SET), Maskinteknisk produktframtagning (MTEK), Funktionella ytor.ORCID-id: 0000-0003-3149-4296
Högskolan i Halmstad, Sektionen för ekonomi och teknik (SET), Maskinteknisk produktframtagning (MTEK), Funktionella ytor.
Högskolan i Halmstad, Sektionen för ekonomi och teknik (SET), Maskinteknisk produktframtagning (MTEK), Funktionella ytor.ORCID-id: 0000-0001-8058-1252
Volvo Power Train Corp., Volvo Group, Göteborg, Sweden.
Visa övriga samt affilieringar
2008 (Engelska)Ingår i: Proceedings of the 13th Nordic Symposium on Tribology, Nordtrib 2008, Tampere: Tampere University Press, 2008, s. 13-Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The presence of cold work material (blechmantel) smeared out on cylinder liners by faulty honing is undesirable as it seals the oil-bearing honing grooves. It is also believed to correlate with increased bore wear, presumably due to its loosening and together with the carbon build-up from the piston’s top land form an increased quantity of abrasive particles. An attempt has been made to estimate the extent of removal of blechmantel for different wear regimes present at the middle and top region (near the top dead centre) of the liner surface using the unworn bottom region as a reference for comparison. A number of truck cylinder liners were axially sectioned after varying periods of engine running under similar conditions of load, engine speed and lubrication. 3D surface measurements were taken at the three regions and a range of standard parameters was extracted. Combining the profile and image analysis, an algorithm was developed to identify and quantify the blechmantel covering the grooves that is most likely to break and act as abrasive wear particles and at the same time it represents the part of blechmantel which covers the most of the surface. It was found out that a mere portion of the blechmantel from the middle and bottom section was removed, while the blechmantel from the top section was greatly removed and thereby it represents one of the possible causes for wear. Axial wear scratches more emphasized on the thrust side of the liner were observed not only through the whole stroke area, but also in the bottom region. The fact that the most of the blechmantel is not removed from the running surface of the liner (except for the very small portion of the polished areas at the dead centres), points out that the blechmantel plays only a minor role on wear of the cylinder liner surfaces.

Ort, förlag, år, upplaga, sidor
Tampere: Tampere University Press, 2008. s. 13-
Nyckelord [en]
Blechmantel, Quantification, Cylinder Liner Wear, Surface Topography
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Identifikatorer
URN: urn:nbn:se:hh:diva-2148Lokalt ID: 2082/2543ISBN: 978-952-15-1961-1 OAI: oai:DiVA.org:hh-2148DiVA, id: diva2:239366
Konferens
13th Nordic Symposium on Tribology, Nordtrib 2008, Tampere, Finland, 10-13 June 2008
Tillgänglig från: 2008-11-18 Skapad: 2008-11-18 Senast uppdaterad: 2018-03-23Bibliografiskt granskad
Ingår i avhandling
1. On Surface Topography of Cylinder Liners
Öppna denna publikation i ny flik eller fönster >>On Surface Topography of Cylinder Liners
2008 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The frictional losses, oil consumption and emissions in internal combustion engines are in great extent controlled by the cylinder liner surface topography. This emphasises the importance of: investigating the liner’s topography by objectively characterising it, investigating its effects on the tribological function to gain a better understanding and improving its manufacturing. As a first attempt in this study to objectively characterise the liner surface, a traditional combination of Scanning Electron Microscope (SEM) images and roughness profiles was used. The groove and image parameters characteristic for liner topographies were extracted by applying specially developed algorithms and together with the standard parameters served to study wear on liners of diesel and petrol engines. An experiment was designed to improve the liners’ manufacturing by varying of the honing process parameters and oil flow simulations were run to study the influence of the characteristics of the manufactured surfaces on their function. The results suggested that reducing the base honing pressure and increasing the plateau honing time gave the best surface with smoother plateaux, summits of higher density and milder slopes, more but smaller islands and shallower valleys. The potentials of fast acquiring and containing 3D data of the interference measurements were utilised to overcome the encountered problems in the usage of the combination of profile and SEM measurements and to enable automatic quality control of the cylinder liner surfaces. In the efforts to examine the influence of the surface properties on liner’s function, the extent of blechmantel (cold work material) removal was estimated from 3D measurements of run liners in engine tests. For characterising this feature, algorithms were developed and implemented and it was found that the most of the blechmantel is still left on the liner pointing that it plays a minor role on wear.

Ort, förlag, år, upplaga, sidor
Göteborg: Chalmers University of Technology, 2008. s. 64
Serie
Report / Department of Materials and Manufacturing Technology, Chalmers University of Technology, ISSN 1652-8891 ; 37
Nyckelord
Cylinder liner, Surface Roughness, Characterisation, Honing, Wear, Blechmantel, Groove Parameters, Quality Control, Flow Simulation
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Identifikatorer
urn:nbn:se:hh:diva-14648 (URN)
Presentation
Delta-Gamma, Hörsalsvägen 7 Chalmers, Göteborg
Opponent
Tillgänglig från: 2011-03-28 Skapad: 2011-03-25 Senast uppdaterad: 2014-03-05Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Personposter BETA

Dimkovski, ZlateAnderberg, CeciliaRosén, Bengt-Göran

Sök vidare i DiVA

Av författaren/redaktören
Dimkovski, ZlateAnderberg, CeciliaRosén, Bengt-Göran
Av organisationen
Funktionella ytor
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 366 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf