hh.sePublikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Topography of as built surfaces generated in metal additive manufacturing: A multi scale analysis from form to roughness
Högskolan i Halmstad, Akademin för ekonomi, teknik och naturvetenskap, Rydberglaboratoriet för tillämpad naturvetenskap (RLAS). University of Lyon, ENISE, Laboratoire de Tribologie et Dynamique des Systèmes, Saint-Etienne, France.ORCID-id: 0000-0002-9447-9635
University of Lyon, ENISE, Laboratoire de Tribologie et Dynamique des Systèmes, Saint-Etienne, France.
University of Lyon, ENISE, Laboratoire de Tribologie et Dynamique des Systèmes, Saint-Etienne, France.
University of Lyon, ENISE, Laboratoire de Tribologie et Dynamique des Systèmes, Saint-Etienne, France.
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Precision engineering, ISSN 0141-6359, E-ISSN 1873-2372, Vol. 52, s. 249-265Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Topographies are one of the challenges for the development of the metal additive manufacturing promising technique. The article investigates multi scale topographies (from form to roughness) of as built surfaces generated by selective laser melting (SLM). Different building inclinations of samples were observed both for upskin and downskin surfaces with a wide range of measuring techniques. The two main aims are: (i) to make a critical review of measuring techniques at different scales, (ii) to enlighten the different surface generation phenomena (and the corresponding scale) occurring during additive manufacturing. The effect of heat treatment on each scale of the topography is also discussed. It is found that the focus variation technique is well suited for AM surfaces. Concerning the observation of the inclined surfaces, some parameters are emphasized as good indicators of typical signatures of AM surfaces: isotropy for the weld track component, the skewness and Rsm for the staircase effect, fractal dimension for the presence of partly melted particles. The different parameters studied helps to model and understand the different surface generation phenomena aforementioned. © 2018 Elsevier Inc.

Ort, förlag, år, upplaga, sidor
Philadelphia, PA: Elsevier, 2018. Vol. 52, s. 249-265
Nyckelord [en]
3D topography characterization, As built surfaces, Form, Metal additive manufacturing, Multi scale measurements, Roughness, Selective laser melting, Staircase effect
Nationell ämneskategori
Produktionsteknik, arbetsvetenskap och ergonomi
Identifikatorer
URN: urn:nbn:se:hh:diva-37820DOI: 10.1016/j.precisioneng.2018.01.002ISI: 000435620800024Scopus ID: 2-s2.0-85040718309OAI: oai:DiVA.org:hh-37820DiVA, id: diva2:1242769
Tillgänglig från: 2018-08-29 Skapad: 2018-08-29 Senast uppdaterad: 2018-08-29Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Cabanettes, FrédéricDimkovski, Zlate

Sök vidare i DiVA

Av författaren/redaktören
Cabanettes, FrédéricDimkovski, Zlate
Av organisationen
Rydberglaboratoriet för tillämpad naturvetenskap (RLAS)
I samma tidskrift
Precision engineering
Produktionsteknik, arbetsvetenskap och ergonomi

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 78 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf