Relaying can increase reliability, range, or throughput. In many cyber-physical systems (CPS), relaying is used to maximize reliability before a given deadline. Since concurrent transmissions are not supported by most CPS, time-division multiple access (TDMA) is typically used. However, a major drawback of relaying in TDMA is that pre-allocated time-slots are wasted if their respective transmitters do not have any correctly received packet to relay. Therefore, in this letter, we propose a novel relay grouping scheme to overcome this drawback. Numerical results show that the proposed scheme significantly enhances the reliability while guaranteeing the deadline for each message. © Copyright 2019 IEEE - All rights reserved.

Many emerging applications based on wireless networks involve distributed control. This implies high requirements on reliability, but also on a predictable maximum delay and sometimes jitter. Further, many distributed control systems need to be constructed using off-the-shelf components, both due to cost constraints and due to interoperability with existing networks. This, in turn, implies that concurrent transmissions and multiuser detection are seldom possible. Instead, half-duplex time division multiple access (TDMA) is typically used. The total communication delay thereby depends on the packet error rate and the time until channel access is granted. With TDMA, channel access is upper-bounded and the jitter can be set to zero. With the aim to reduce the packet error rate given a certain deadline (a set of TDMA time-slots), we propose a novel relaying scheme, which can be implemented on top of off-the-shelf components. The paper includes a full analysis of the resulting error probability and latency. Numerical results show that the proposed relaying strategy significantly improves reliability given a certain maximum latency, or alternatively, reduces the latency, given a certain target reliability requirement. © 2016 IEEE.

Using relayers in wireless networks enables higher throughput, increased reliability or reduced delay. However, when building networks using commercially available hardware, concurrent transmissions by multiple relayers are generally not possible. Instead one specific relayer needs to be assigned for each transmission instant. If the decision regarding which relayer to assign, i.e., which relayer that has the best opportunity to successfully deliver the packet, can be taken online, just before the transmission is to take place, much can be gained. This is particularly the case in mobile networks, as a frequently changing network topology considerably affects the choice of a suitable relayer. To this end, this paper addresses the problem of online relay assignment by developing a low-complexity algorithm highly likely to find the optimal combination of relaying nodes that minimizes the resulting error probability at the targeted receiver(s) using a mix of simulated annealing and ant colony algorithms, such that relay assignments can be made online also in large networks. The algorithm differs from existing works in that it considers both unicast as well as broadcast and assumes that all nodes can overhear each other, as opposed to separating source nodes, relay nodes and destination nodes into three disjoint sets, which is generally not the case in most wireless networks.

Wireless automation and control networks, with stringent latency and reliability requirements, typically use half-duplex communications combined with deadline-aware scheduling of time slots to nodes. To introduce higher reliability in legacy industrial control systems, extra time slots are usually reserved for retransmissions. However, in distributed wireless control systems, where sensor data from several different nodes must be timely and reliably available at all places where controller decisions are made, this is particularly cumbersome as all nodes may not hear each other and extra time slots imply increased delay. To enable all-to-all broadcast with manageable overhead and complexity in such systems, we therefore propose a novel relaying strategy using packet aggregation. The strategy assigns relayers to time slots, as well as determines which packets to aggregate in each slot, using a low-complexity algorithm such that ultra-reliable communications can be obtained with maintained end-to-end latency.

Platooning is widely considered a promising approach to decrease fuel consumption by reducing the air drag. However, in order to achieve the benefits of aerodynamic efficiency, the inter-vehicle distances must be kept short. This implies that the intra-platoon communication must not only be reliable but also able to meet strict timing deadlines. In this paper, we propose a framework that reliably handles the co-existence of both time-triggered and event-driven control messages in platooning applications and we derive an efficient message dissemination technique. We propose a semi-centralized time division multiple access (TDMA) approach, which e.g., can be placed on top of the current standard IEEE 802.11p and we evaluate the resulting error probability and delay, when using it to broadcast periodic beacons and disseminating eventdriven messages within a platoon. Simulation results indicate that the proposed dissemination policy significantly enhances the reliability for a given number of available time-slots, or alternatively, reduces the delay, in terms of time-slots, required to achieve a certain target error probability, without degrading the performance of co-existing time-triggered messages. © 2015 IEEE

Platooning is both a challenging and rewarding application. Challenging since strict timing and reliability requirements are imposed by the distributed control system required to operate the platoon. Rewarding since considerable fuel reductions are possible. As platooning takes place in a vehicular ad hoc network, the use of IEEE 802.11p is close to mandatory. However, the 802.11p medium access method suffers from packet collisions and random delays. Most ongoing research suggests using TDMA on top of 802.11p as a potential remedy. However, TDMA requires synchronization and is not very flexible if the beacon frequency needs to be updated, the number of platoon members changes, or if retransmissions for increased reliability are required. We therefore suggest a token-passing medium access method where the next token holder is selected based on beacon data age. This has the advantage of allowing beacons to be re-broadcasted in each beacon interval whenever time and bandwidth are available. We show that our token-based method is able to reduce the data age and considerably increase reliability compared to pure 802.11p. © 2015 IEEE.

Many emerging applications based on wireless networks involves distributed control. This implies high requirements on reliability, but also on maximum delay and sometimes jitter. The total delay depends on the packet error rate and the time until channel access is granted. With e.g., TDMA, channel access is upper-bounded and the jitter zero. To reduce the packet error rate given a certain deadline (a set of TDMA time-slots), we propose a simple relaying scheme, including a full analysis of its resulting error probability and delay. Numerical results show that the proposed relaying strategy significantly improves reliability given a certain message deadline.

Lately, all the top truck manufacturers are investing considerable resources in the research and development of platooning systems which would allow vehicles to save fuel and improve safety by travelling in a close-following manner. The platooning system requires frequent and reliable vehicle-to-vehicle communications. As platooning takes place in a vehicular ad hoc network, the use of IEEE 802.11p is close to mandatory. However, the 802.11p medium access method suffers from packet collisions and random delays. Most ongoing research suggests using TDMA on top of 802.11p as a potential remedy. However, TDMA requires synchronization and is not very flexible if the beacon frequency needs to be updated, the number of platoon members changes, or if re-transmissions for increased reliability are required. We therefore suggest a token-passing medium access method where the next token holder is selected based on beacon data age. This has the advantage of allowing beacons to be re-broadcasted in each beacon interval whenever time and bandwidth are available. We show that our token-based method is able to reduce the data age and considerably increase reliability considerably compared to pure 802.11p.

Autonomous driving in road trains, a.k.a. platooning, may reduce fuel consumption considerably if the intervehicle distances are kept short. However, to do this, the intraplatoon communication must not only be reliable but also able to meet strict deadlines. While time-triggered messages are the foundation of most distributed control applications, platooning is likely to also require dissemination of event-driven messages. While much research work has focused on minimizing the age of periodic messages, state-of-the-art for disseminating eventdriven messages is to let all nodes repeat all messages and focus on mitigating broadcast storms. We derive an efficient message dissemination scheme based on relay selection which minimizes the probability of error at the intended receiver(s) for both unicast and broadcast, without degrading the performance of co-existing time-triggered messages. We present a full analysis of the resulting error probability and delay, when relayers, selected by our algorithm, are used to disseminate messages within a platoon. Numerical results indicate that the proposed relaying policy significantly enhances the reliability for a given delay.

Wireless networks present a promising alternative to the currently used wired systems as they are more flexible, easier to install and maintain. However, requirements on reliability and timeliness which at present are met by wired networks, also need be fulfilled by wireless solutions. Relaying and packet aggregation have been recognised as viable tools to do this. However, introducing additional relay nodes into an industrial network is costly. Hence, in this paper we propose to use a combination of relaying and packet aggregation performed by the source nodes themselves. The results show that our proposal improves performance considerably, but also that the transmission schedule plays a crucial role. A schedule adapting to the varying channel conditions, improves the performance substantially. By carefully choosing which packet to aggregate, even further improvements can be achieved. © 2015 IEEE.